How To Connect Ip Camera To Laptop Using Poe Injector

January 18, 2019.

We're oft asked how to modify an IP camera's video settings one time you already have it up and running on your NVR. This process can be difficult without any knowledge of computer networking or setting up a standalone IP camera. In this commodity we explain the technical details of taking a camera from the back of your NVR and connecting to it with either a direct connection or through your network.

Removing the Camera from the NVR

Our IP security cameras have a plethora of settings that can be accessed from the camera'due south built-in web interface. When a photographic camera is connected to a NVR with built-in PoE, information technology receives IP address and configuration settings from the NVR to proceed it on an internal network. While this is keen for network security reasons, it prevents directly access to the web interface of the photographic camera. If the user wants to change the camera's shutter charge per unit, or IR LED strength, the photographic camera would demand to be disconnected from the NVR and accessed from a computer.

The offset steps include understanding how a camera and PoE NVR piece of work together, noting the IP accost the photographic camera is configured to and finally physically removing the camera from the NVR. The video beneath discusses these concepts in detail.

How to Connect To Your PoE IP Photographic camera from a Computer - Introduction

After having a grasp on the basics and noting the IP accost of your camera you can and so continue to the next steps. In that location are ii ways that you can connect to a photographic camera'south web interface:

1. 1. The first is through a direct connectedness into your Windows desktop or laptop that has an ethernet port.
   2. The 2nd involves going over your computer network by configuring the camera to communicate on the network.

Be sure to note the IP address of the camera before disconnecting it from the NVR, yous will need information technology later.

A) Direct connexion between IP camera and Reckoner

The easiest way to admission an IP photographic camera is by connecting to it directly from a computer. This method requires you lot have the following:

1. The IP accost of your camera from the NVR registration page
2. PoE Injector or 12VDC 1A Power Adapter. It is very important to use a CCTV Camera World canonical device or you take chances frying the camera due to incorrect voltage
3. Ii Ethernet cables (one if using a power adapter)
4. Windows 10 based PC

The below video shows the entire process from start to cease.

How to Connect an IP photographic camera directly to a computer

one. Utilise a PoE injector to supply power and information

A PoE injector will have two ports, ane labeled for PoE or P+D/Out (power and information) and 1 labeled LAN or Data/In. Connect the PoE injector to a power outlet. Connect an ethernet cable from your PC'southward network port to the Data/In on the PoE injector. Connect a 2nd ethernet cable from the network camera's RJ45 network jack to the port labeled PoE or P+D/Out. To bank check if everything is connected properly refer to the lights on the PoE injector and the port on your computer. If you practice not see any indication lights you may have a bad cable or do not have the wires continued properly.

2. Employ a 12VDC 1A power adapter

A right power adapter will have a label stating it is 12VDC 1000mA. If y'all have any concerns about the correct power supply please feel free to email our support team. Ability the camera by connecting the adapter. Connect an ethernet cable from the camera directly to your figurer'south ethernet port. A good way to cheque if the camera is receiving power and communicating with your computer is to look at the lights on your computer'southward port. If you take no lights it is important to examination that your cablevision and power supply work with some other device.

three. Configure your PC'southward network port to communicate with the camera

For your reckoner to "speak" to your camera, yous demand to set its network port to the same IP accost scheme equally the camera. Before we disconnected the photographic camera from the back of the NVR, nosotros noted what the IP address of the camera was.

Login to your Windows PC, change your computer's ethernet adapter to communicate with the camera. Employ the Network & Internet settings which contains an Ethernet section. Using the change adapter settings set an IP address for your computer that matches the network for the camera. If you do not know how to do this refer to the video to a higher place for this step.

4. Test the connexion with the Ping command

Afterwards powering the camera and configuring your computer to talk with it, it is adept practice to examination the connection using the Ping command. But open the Command Prompt and blazon Ping with the address of the camera. In our example we used the following command: ping x.1.1.65

v. Access the camera using Internet Explorer

It is important to use Internet Explorer equally it is the most uniform browser for accessing security cameras. Blazon the IP address of your camera into the address bar in Internet Explorer. Some cameras may require initialization and it is recommended to uncheck the Easy4IP and auto-update options when proceeding through the prompts. The countersign can be admin, or may exist printed on the characterization found on the box of the photographic camera. Notation: the customer is responsible for any password change beyond the defaults. There is no principal reset password.

After successfully logging into the camera you demand to install a plugin to view the photographic camera. Click the link in the center of the page to download the plugin. Make certain to Run and exercise non save the plugin download. Internet Explorer will prompt y'all to let the plugin to run. One time the plugin is installed, yous volition be required to log dorsum into the camera. You should now run across video from your photographic camera and can modify the settings of the photographic camera in the Setting tab within your browser. Make sure when you are done modifying your camera(southward) that y'all modify your network settings back to "Obtain IP accost automatically" in your network settings, this is demonstrated in the video above.

B) Accessing the photographic camera over your network

Besides direct connection to a computer, the other method to connect to a PoE security camera is over the network. This method requires the following pre-requisites:

1. A home or business network with router
2. Windows PC with ConfigTool installed
3. PoE Injector or 12VDC 1A ability adapter
4. A network cable to connect to your router
5. The IP address of your photographic camera

The video below shows the process in detail.

How to access a PoE security camera from a computer - Over a Network

1. Power the camera like you would for the previous method

As shown in the video, you can use a PoE injector or 12V DC 1amp power adapter to power the camera and connect to your network router or switch. The process is simple. It is very important to apply a CCTV Camera Earth approved device or you risk frying the camera due to incorrect voltage.

2. Connect the photographic camera to your network router

Instead of connecting the photographic camera straight to your computer, you will connect information technology to your network router so the computer can communicate with the camera over the network. When following this guide, it is important to connect the camera and estimator to the same router or switch. We suggest using a hardwired connexion between the computer and the router to forbid a state of affairs where your WiFi network is different from the wired network. If you lot are knowledgeable about your network setup, feel free to utilise a WiFi laptop.

3. Utilise the ConfigTool to observe the camera and change its IP accost

Using the ConfigTool to notice the camera on your network is fairly easy and is covered in our guide on how to connect a network surveillance photographic camera to a computer. It is imperative that you plow off whatsoever firewall or antivirus program on your estimator that may forestall the programme from sniffing your network.

iv. Admission the camera's web interface using Internet Explorer

The steps are similar to method A because the web interface will be the aforementioned regardless of how you connect to the camera.

Matt Rossi is a Technical Support Director at CCTV Camera World, a leading CCTV Camera distributor located in Buffalo, NY. He is a technical support expert for everything video surveillance related.

Connect with Matt via: Facebook

Source: https://www.cctvcameraworld.com/access-poe-security-camera-from-computer/

Posted by: fernandezheratat.blogspot.com

Share this post